CeLAN Printer Module Tester/Demo Interface

CO-T-Print

Remote Memory Module

CE-RMM

The CeLAN Remote Memory Module (RMM) captures system events on a removable SD card that can be read on a PC. The module also includes a zone input that can be used as a tamper or any other system input.

Features:

• Allows for up to 32 GB of system event history.
• Redundant, Primary and Secondary SD slots allows for continuous recording of events while allowing review of recent events.
• Single Input Zone for use as tamper, or any other zone application.
• Mounts inside Protector and Protector II Accessory Enclosure Includes Accessory hardware kit.
• CINCH Stick upgradeable firmware.

TCP Module

CE-TCP

A dual-application device that allows:

• Stand-Alone Mode 1: Connect up to five separate supervised inputs for remote reporting, and remotely command one on-board relay.
• Protector and Protector II CeLAN Mode: Communicate status remotely, interact with the Protector and Protector II System remotely (when allowed), and extend the CeLAN BUS via TCP/IP (when allowed).

When used in the stand alone mode the TCP/IP Module uses AES encryption to allow for secure communication between the module and a remote monitoring station. Status of up to 5 supervised inputs and remote operation of one on-board relay.

When used in Protector and Protector II CeLAN mode, the TCP/IP Module uses AES encryption for secure communications between Protector and Protector II System and TCP/IP Module, and:

• Remote monitoring stations
• Remote TCP/IP Modules
• Remote SMS (Security Management Systems)

TCP/IP module comes with five 3.0K ohm EOL resistors and mounting hardware (screws and anchors).

Power for the CeLAN TCP/IP Module:

• Protector and Protector II 12 VDC CeLAN power terminals.
• CeLAN Remote Power Supply Module, or
• Separate 12 VDC-power supply capable of delivering up to 250 mA
• CeLAN AES encrypted digital data bus technology provides secure, fast and reliable data transfer between the Protector and Protector II Panel and CeLAN modules.

Features:

• 128-bit AES Encrypted CeLAN communications.
• 256-bit AES Encrypted TCP/IP communications.
• Five (5) fully supervised input zones.
• Five (5) state zones:
• Open Circuit
• Supervised Circuit (3k EOL)
• Short Circuit
• Ground Fault High
• Ground Fault Low
• One (1) Relay output
• Guaranteed Delivery 32k on-board message buffer.
• On-board LED power and CeLAN bus status indicators.
• CeLAN AES encrypted technology for security, easy setup and enhanced performance.
• Can be mounted in all compatible cabinet enclosures, sold separately.
• CINCH Stick Field upgradeable software.

Remote Power Module

CE-RP

The CeLAN Remote Power Module is a dual-application device that allows use in either stand-alone mode or in fully supervised CeLAN expansion module mode.

Stand-Alone Mode:

• Supervised 5 Amp, 12 VDC power supply.
• Two on-board Form-C relays provide supervision status of:
• AC input to the module
• Back-up battery status
• AES Encrypted CeLAN communications
• Supervised 5 Amp 12 VDC Power Supply
• One hardware input zone per module
• Five (5) state zones:
• Open Circuit
• Supervised Circuit (3k EOL)
• Short Circuit
• Ground Fault High
• Ground Fault Low
• Two (2) Form-C relays that are fully programmable and controllable by the Protector and Protector II system.
• On-board LED power and bus status indicators.
• On-board LED current-load indication.
• CeLAN AES encrypted technology for security, easy setup and enhanced performance.
• ‘CINCH Stick field Upgradeable software.
• On-Board LED’s display the percentage of current being used on each 12VDC channel.

CeLAN Expansion Module

Ce-Ex

The CINCH Systems CeLAN Expander Module (EX), simplifies your installation by allowing you to interconnect up to 10 different CeLAN devices / wire-runs (+12 VDC, Bus A, Bus B, GND), on separate terminals. It also provides three sets of additional power and ground terminals for other powered devices. The module can be mounted into the Protector and Protector II Enclosure, Protector and Protector II Accessory Enclosure, or Custom Plastic CeLAN Enclosure w/wall & cover tamper.

Features:

• Ten 4-position terminal blocks for CeLAN Expansion (+12 VDC, Bus A, Bus B, GND).
• Three 2-position terminal blocks (+12 VDC, GND), for power expansion to other powered devices.
• Mounts inside Protector and Protector II, Protector and Protector II Accessory, or Enclosure- CeLAN Custom Plastic w/wall & cover tamper.
• Includes Accessory hardware kit.

CeLAN  Expansion Module
DIN Rail Mounted

Ce-Ex-DIN

The CINCH Systems CeLAN Expander Module (EX) mounted on a DIN rail, simplifies your installation by allowing you to interconnect up to 10 different CeLAN devices / wire-runs (+12 VDC, Bus A, Bus B, GND), on separate terminals. It also provides three sets of additional power and ground terminals for other powered devices. The module can be mounted into the Protector and Protector II Enclosure, Protector and Protector II Accessory Enclosure, or Custom Plastic CeLAN Enclosure w/wall & cover tamper.

Features:

• Ten 4-position terminal blocks for CeLAN Expansion (+12 VDC, Bus A, Bus B, GND).
• Three 2-position terminal blocks (+12 VDC, GND), for power expansion to other powered devices.
• Mounts inside Protector and Protector II, Protector and Protector II Accessory, or Enclosure- CeLAN Custom Plastic w/wall & cover tamper.
• Includes Accessory Hardware kit

Translator Module

Ce-T422

The CINCH Systems CeLAN RS422 Translator  Module expands the versatility of Rampart System by adding the capability to use 3rd party interface products to also control the operation of vehicle barriers, gates or other similar devices.

• Connect both touch screen controls (Ce-TS-VBS) along with 3rd party controls (Proface, Indusoft, Wonderware, etc) to operate the same or different gates.
• The Ce-T422 acts as the translator interface and firewall between the Rampart system and the 3rd party interface product.  Advanced design allows direct commands to either the Rampart panel or to 3rd party interface products.
• Provides a consistent interface for reliable operation of the system that the integrator can use without requiring custom firmware to be written for the module for each project. The Ce-T422 Modbus interface allows the integrator to customize the 3rd party interface products to meet the needs of the customer.
• For added security and reliability the Ce-T422 has dual CeLAN inputs so it can maintain a redundant, secure communications path to the rampart panel.  In redundant CeLAN mode the Rampart panel utilizes both CeLANs when sending messages to the module adding to the security provided by the AES encryption.  In the event of a single CeLAN failure the Rampart panel can still communicate with the module using the remaining CeLAN.

The Rampart System can monitor and control up to 20 vehicle barrier, gates or similar systems per panel and allows for up to 100 CeLAN devices to be connected to its dual CeLANs.

To simplify installation and troubleshooting there are 4 LEDs on Board:

- 1 - Green uC (microcontroller) operating normal LED.

- 2 - Red CeLAN communications LED.

- 1-  (Proface) 3rd party [RS422 Modbus] communications LED.

• 4-pin CINCH Stick port on board allows firmware upgrades in the field for additional functionality without having to replace the hardware.
• Power for the CeLAN RS422 Translator Module is provided by:
• Rampart 12 VDC CeLAN power terminals.
• CeLAN Remote Power Supply Module, or separate 12 VDC-power supply capable of delivering up to 25 mA.
• Redundant CeLAN AES encrypted digital data bus technology provides secure, fast and reliable data transfer between the Rampart Panel and CeLAN modules.
• Features:
• Redundant AES Encrypted CeLAN communications.
• RS422 Modbus communications.
• Can be mounted in all compatible cabinet enclosures.
• CINCH Stick field upgradeable software.

Specifications:

• Power Requirements: 12VDC nominal, 10 VDC minimum, 14 VDC maximum, 40 mA minimum.
• Panel Data Bus: CeLAN – 128 bit AES Encrypted.
• Wire gauge supported:  18AWG – 22AWG.
• Dimensions:  4.5” x 3.4” (114.3 mm x 86.4mm).
• Operating Temperature: 32° F to 120° F  (0° C to 49° C), up to 140° F (60° C) under temporary conditions
• Maximum Humidity: 85+/- 5% relative humidity, noncondensing, 86° F +/- 3° F.

Multimode Fiber Conversion Module

Ce-FC-R

The CeLAN Fiber Conversion Module expands the versatility of Protector and Protector II Panel by allowing the CeLAN to be converted from standard copper wires to a dual fiber. On Protector and Protector II Systems, you can connect multiple fiber conversion modules to a single panel as needed to provide secure communications.

The fiber optic communication performance can readily be determined via the on-board LED Fiber Strength Meter. The meter uses 5 LEDs  - one red and 4 green  to display the strength of the fiber signal coming in from the other CeLAN Fiber Conversion Module and is a readily recognized in a ‘cell phone’ like signal strength display.

Multimode Fiber

Acc-CFC-MM

Multimode fiber is mostly used for communication means over shorter distances, as within a building. Typical multimode links have data rates of 10 Mbit/s to 10 Gbit/s over lengths up to 600 meters.  Multimode fiber has a larger core size allowing for simpler connections, normally orange in color (may differ in some locations).

Entended Range MM Fiber Conversion Module

Ce-FC-ER

Expands the versatility of CINCH’s control panels by allowing the CeLAN to be converted from standard copper wires to a dual fiber. Connect multiple fiber conversion modules to a single panel as needed to provide secure communications.

• CeLAN AES encrypted technology for security, easy setup and enhanced performance.
• 5 LED Bar Graph Fiber Signal Strength display.
• ST/SC Fiber Connectors.
• One (1) fully supervised input zone.
• Five (5) state zones:
• Open Circuit.
• Supervised Circuit (3.0k EOL).
• Short Circuit.
• Ground Fault High.
• Ground Fault Low.
• On-board LED power and CeLAN bus status indicators.
• CINCH Stick field upgradeable firmware.
• Includes Accessory hardware kit.

Multimode Fiber

Acc-CFC-MM

Multimode fiber is mostly used for communication means over shorter distances, as within a building. Typical multimode links have data rates of 10 Mbit/s to 10 Gbit/s over lengths up to 600 meters.  Multimode fiber has a larger core size allowing for simpler connections, normally orange in color (may differ in some locations).

Entended Range SM Fiber Conversion Module

Ce-FC-S

Expands the versatility of CINCH’s control panels by allowing the CeLAN to be converted from standard copper wires to a dual fiber. Connect multiple fiber conversion modules to a single panel as needed to provide secure communications.

Expands the versatility of CINCH’s control panels by allowing the CeLAN to be converted from standard copper wires to a dual fiber.  Connect multiple fiber conversion modules to a single panel as needed to provide secure communications.

• CeLAN AES encrypted technology for security, easy setup and enhanced performance.
• 5 LED Bar Graph Fiber Signal Strength display.
• ST/SC Fiber Connectors.
• One (1) fully supervised input zone.
• Five (5) state zones:
• Open Circuit
• Supervised Circuit
• (3.0k EOL)
• Short Circuit
• Ground Fault High
• Ground Fault Low
• On-board LED power and CeLAN bus status indicators.
• CINCH Stick Field Upgradeable firmware.
• Includes Accessory hardware kit.

Single Mode Fiber

Acc-CFC-SM

Single mode fiber is used where a high precision communication means is required. Better performance over long distances. Single mode fiber has a smaller core, and normally yellow in color (may differ in some locations).

Data Bus Isolator

Ce-Isolator

The CeLAN Isolator Module provides filtering of unwanted signals on the CeLAN data bus. Have confidence installing in a noisy environment.

Clean-up the “noise” from:

• Lighting
• Audio Components
• Power Generators
• High Voltage

When to use it:

• Remove damaging A/C induced on the data line due to improper wiring with high voltage wiring or other noisy electronic wiring.
• To remove any unintended intelligence bearing signals that may me riding on the data line.
• Extend the length of the CeLAN. Protect systems from damaging ground loops.
• Isolate one set of CeLAN devices from another set of CeLAN devices.

Multi-Mode Fiber Cable

Acc-CFC-MM

Multimode fiber is mostly used for communication means over shorter distances, as within a building. Typical multimode links have data rates of 10 Mbit/s to 10 Gbit/s over lengths up to 600 meters.  Multimode fiber has a larger core size allowing for simpler connections, normally orange in color (may differ in some locations).

Single-Mode Fiber Cable

Acc-CFC-SM

Single mode fiber is used where a high precision communication means is required. Better performance over long distances. Single mode fiber has a smaller core, and normally yellow in color (may differ in some locations).